North East Trailer Sailors

Public and Members Only forums
It is currently Fri Oct 20, 2017 7:26 am

All times are UTC - 5 hours




Post new topic Reply to topic  [ 2 posts ] 
Author Message
 Post subject: BoatTrailer Extension "The Full Beam Reach"
PostPosted: Sat Aug 26, 2017 7:57 pm 
Offline
tadpole

Joined: Wed Jun 21, 2017 9:33 pm
Posts: 2
Boat_year: 1996
Boat Make: Com Pac
Boat_Model: 16 ll
Boat_Name: Passing Wind
DSC_number: 0
Attachment:
BeamReachBpat.jpg
BeamReachBpat.jpg [ 162.26 KiB | Viewed 968 times ]
Yo' Trailer sailors:
BOAT TRAILER EXTENSION PROJECT:

I have made a major modification to my CP 16 ll trailer in an attempt to gain more distance between the tow car hitch and the bow- but only for the launch. The design allows a fast 5 or 6 feet of strong steel extension without even touching your trailer hitch. I wish to share the results with my fellow Com Pac sailors.

I had some minimum feature requirements for the design-
1. Add at least 5 feet of trailer extension.
2. Maintain trailer strength
3. Design so that the hitch does NOT need to be disconnected from the towing vehicle.
4. Design so that no new hardware gets mounted under the trailer.

Here is what I came up with and built: (I will post pics and a video later)
First, I removed the female portion of the hitch from the north end of the trailer and pulled the trailer light wires from the cavity. (My trailer frame is 3" x 2").
Then I bolted the removed section of the hitch to a 10" section of 2" x 3" square stock (rectangular) 1/4" steel. I re-used the existing 1/2" bolts, drilling through the steel with a 1/2" carbide bit (and foam cutting oil). Now it gets good~~~ I inserted one end of a 7' steel 2 1/2" x 1 1/2" square stock inside of the 10" hitch steel. I double bolted this together and though perhaps overkill- welded the south end of this bolted combination together. So to be clear- I now have the female part of the hitch well secured to the end of a 7' piece of steel that will fit / slide nicely inside the cavity of the front center of the trailer. I then slid the unit into said cavity until the mounted hitch section stopped it. With the 1/2" cobalt drill bit, I drilled through the trailer frame with the sliding extension steel in place inside about 6" back from the hitch, then at 18" back and 6' back from the hitch. These holes secure the 7' extension steel in place in the "towing position" secured with 1/2" x 4" tractor pins. You could use bolts. To use the "Extension" park at a level section before a ramp, block the trailer wheels, unplug the trailer lights and pull the tractor pins out. Drive forward 5' until the back hole in the extension meets the frame hole that is 18" back from the hitch. While there are a number of ways to tell when the holes are exactly lined up lets assume you have someone watching for your. When the holes in the frame line up with the holes in the extension, insert the tractor pins (or bolts, etc) and enjoy the extra 5 feet of strong trailer extension! Just to be super clear: This design is never intended to tow with in the extended position. Just in and out of the ramp.

Fine print you need NOT read unless you are followng this step by step to build it:
Obviously, you will need to re-attach the trailer light wires outside the frame with quick ties and waterproof heat shrink wire connectors.
Actually, the 7' section slides into the 10" section where the hitch attached after you remove the back bolt of the hitch and slide the 7' section up to the front bolt. Then drill through the 7' section using the back holes from the removed bolt as a guide. This secures the 7' extension directly to the female portion of the hitch, in addition to the other bolts you will add mentioned above.
I elected to go with a 5' extension but you can get 6 or 7 feet by starting with an 8' raw extension and leaving only 1' or so double pinned at full extension. These 1/2" tractor pins have handles and cotter pins. Tractor Supply sells them.
Drilling through both sides of the trailer frame with the two sides of 1/8" steel inside takes time. Keep the drill medium slow, lots of cutting oil (I used the foam cutting oil) or a teflon spray. You really should use a $15 - $20 cobalt bit.


Attachments:
File comment: Showing the extended "Full Beam Reach" in the extended position.
BeamReachSm.jpg
BeamReachSm.jpg [ 163.61 KiB | Viewed 968 times ]
File comment: Here is the beam going into the trailer- held bu 1/2" tractor pins. The rod on the right drops when the beam is pulled out enough
BeamReachSouth.jpg
BeamReachSouth.jpg [ 132.1 KiB | Viewed 968 times ]
Top
 Profile Send private message E-mail  
 
 Post subject: Re: BoatTrailer Extension "The Full Beam Reach"
PostPosted: Mon Aug 28, 2017 10:10 am 
Offline
sailfish

Joined: Wed Apr 17, 2013 9:21 am
Posts: 114
Location: Charlton, MA
Boat_year: 1977
Boat Make: Macgregor
Boat_Model: V25
Boat_Name: Tsatzsue
DSC_number: 0
I like it!!

Every inch both laterally and vertically counts.

Ken B.


Top
 Profile Send private message E-mail  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 2 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
cron
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group